divinepasob.blogg.se - Easyweather 8.8

Easyweather 8.8 Patch#
Easyweather 8.8 upgrade#
Easyweather 8.8 software#
Easyweather 8.8 code#
Easyweather 8.8 download#

Both final version and patch can be downloaded here.

Easyweather 8.8 upgrade#

Since the final version of Cumulus 1 cleared most of the bugs present in earlier releases (not quite all, this is still a bug relating to reading pressure from Fine Offset stations), it is to your benefit to upgrade to final legacy release and apply the patch to the GUI. If you are still using an earlier version of Cumulus 1, it cannot be assumed that all parameters that do not apply to your version are identified. It can be assumed that all parameters marked as applicable to Cumulus 1, do apply to the final formal release. It was updated each time there was a major release, some updates mention the release that introduced that parameter. This page was originally created when only Cumulus 1 was available. There is no source available for Cumulus 1, so nobody can check what read-only parameters are available against what is documented below. The read-write parameters are correct, as they have been checked against Configuration screens.

Each contributor may also add/edit entries because of a personal experience of using a particular parameter.

Easyweather 8.8 software#

Steve Loft also described in his posts on the forum a number of parameters and how they are used (hopefully all those have been copied into this page, but on 2 June 2008, Steve Loft swapped to new forum software and did not retain any posts prior to then, so there is no way to check the relevant posts between 2003 when the software was first released and May 2008).

Steve Loft (as developer) did make some entries that are retained on this page (those should be correct).

There have been over a thousand builds of Cumulus version 1.

Easyweather 8.8 code#

The problem is that Steve Loft lost some of his documentation and admitted he could not remember all parameters his code could process. There is no guarantee that all configuration parameters that can be used (if you are running the original software) are in this list There are no references to which parameters apply to Cumulus 2, as that flavour of the software is not available nowĬompleteness for original Cumulus software.To make it easier to navigate larger tables, read-only and read-write parameters may be grouped under relevant sub-heading within the table.As explained later, some parameters are read-only, and some are read-write.A parameter may be defined in multiple sub-sections, if its definition needs to be explained differently according to weather station types.Some sections can take a lot of parameters, and for these sub-sections may be added, that allow you to navigate directly to them from the table of contents.Cumulus.ini uses sections, thus the first way that the list is divided is by the relevant section where the parameter must be placed.You will find that the table listing parameters available is divided in multiple ways: The parameters listed can change the look of Cumulus, can hold basic information about your location, can amend the way Cumulus interfaces with your weather station, can hold the settings used to interface with your website, and with various external websites. When Cumulus restarts it will read the file again and see any edits you have made. If you do need to edit the file, close Cumulus first to ensure you are working on latest contents, and your edit cannot conflict with any edit Cumulus may be making.Note this Cumulus save action may change the order, or add lines, compared to any file that you manually edited.The file shows as 'modified date' the last time that Cumulus was shut down, the file will contain the contents of the application's configuration screens and also any parameters that were in any previous copy of the file that cannot be configured within Cumulus.

Cumulus creates a new version of this file when it shuts down, if this is the first run of the software this will create the file for first time.

Easyweather 8.8 download#

When Cumulus is run for very first time, the file does not exist, as it is not included in the download (of legacy Cumulus). It is only read when Cumulus starts up.Cumulus.ini is a text file containing initialization parameters used by the Cumulus 1.x.x software application.4.3.10 Sections dealing with interfaces to external sites.4.3.2.6 Reading File instead of weather station.4.3.2.5 Introduced for problems with Fine Offset family:.4.3.2.2 Read-Write parameters in the Station section.4.3.2.1 Read-only parameters in the Station section.3.3 Read-only Settings independent of application.3.2 Read-write Settings controlled by application.1.1 Completeness for original Cumulus software.